CAJ Innovations Forums - Optimiser for Android

996SPS Junior Member Offline ducati with P8 Posts: 60 Finland	Re: Optimiser for Android Reply #90 - 05/02/13 at 00:13:11 Actually I use google drive. And I can't figure out how to dl the file from there. The phone tries to open it which of course does not succeed.
Back to top	http://myducati.wordpress.com IP Logged

Indy40

YaBB Newbies

Offline

I love MyECU!

Posts: 19
France
Gender: male

Re: Optimiser for Android
Reply #91 - 05/05/13 at 06:40:59

Hi All !
First of all, thanks to 996SPS for his help. I endly got the BT working with his advice.
I think I am in the right direction to finalize a good map for my 916. I have to buy a LC1 to improve the accuracy of my analysis.

I just want to share today's issue with you.
I try to load an updated map last week with the android optimiser. It seems to work well, and I check the job by download it after and then check the files.
As usual, some changes in the numbers ...
but lots of them in fact !
SparkAdv moves a little as usual, but also InjAdv and InjDur. And for InjDur, the changes were so high that it completly kills the improvement put in the file !
I try to upload and download several times, same results.
A very annoying point is the TPS value change : I request a TPS=1 and gets each time in the download file TPS=150 !!!

I just think about Cliff advices in the past and then use the ECU Controller 1.66 with the cable ...
and ...
it works, with very slight changes in the SpkAdv table.
I got the files if necessary if it can help to fix some problems.
Regards !

Back to top

IP Logged

YaBB Administrator YaBB Administrator Offline I love YaBB! Posts: 679 The Land of YaBB	Re: Optimiser for Android Reply #92 - 05/05/13 at 07:20:29 The changes are due to rounding but the Android Optimiser shouldn't be producing significantly more. Can you send me the before and after maps and the log file that produced it.
Back to top	The Administrator. IP Logged

Indy40

YaBB Newbies

Offline

I love MyECU!

Posts: 19
France
Gender: male

Re: Optimiser for Android
Reply #93 - 06/16/13 at 00:00:33

Just to let you know that my latest test with a better interpolated map allows me to "rediscover" my bike.
Great acceleration and driveability, even if some minor adjustment will be requets at idle.
As i got a LC1 on the bike now, lots of data to analyze and optimize. i will test soon the closed loop mode.
SO : Thanks a lot to Cliff for all that developpment job !

I still got the map loading issue explained further with the BT module, but it works fine with the ECU Controller.

Regards !

Back to top

IP Logged

Mad Farquhar Full Member Offline Slainthe mhath Posts: 171 Black Isle, Scotland Gender:	Re: Optimiser for Android Reply #94 - 06/20/13 at 02:01:30 Is it me or is the latest version of myECU android optimiser on the website (0.94) in the wrong format ?
Back to top	MG Sport 1100 inj Triking Honda ST1100 V7 Stone IP Logged

COnewbie Full Member Offline 97 Sport1100i My16M MkVII 2 LC-1s Posts: 120 Central Oregon, USA Gender:	Re: Optimiser for Android Reply #95 - 06/20/13 at 03:02:53 You're right. The link is pointing to the AndroidOptimiser manual in .odt format, not the App itself. Odt is the Open Document Format version. LibreOffice can read that format. It's free, and it reads MSOffice formats, too.
Back to top	44 1/2 degrees North, 1036m up. IP Logged

Mad Farquhar Full Member Offline Slainthe mhath Posts: 171 Black Isle, Scotland Gender:	Re: Optimiser for Android Reply #96 - 06/20/13 at 16:45:41 Aye, that's what I thought. CAJ must have a lot on his mind.
Back to top	MG Sport 1100 inj Triking Honda ST1100 V7 Stone IP Logged

YaBB Administrator YaBB Administrator Offline I love YaBB! Posts: 679 The Land of YaBB	Re: Optimiser for Android Reply #97 - 06/20/13 at 16:48:38 Oops, sorry about that. Will fix right now.
Back to top	The Administrator. IP Logged

YaBB Administrator YaBB Administrator Offline I love YaBB! Posts: 679 The Land of YaBB	Re: Optimiser for Android Reply #98 - 06/20/13 at 17:16:20 Should be fixed now.
Back to top	The Administrator. IP Logged

Mad Farquhar

Full Member

Offline

Slainthe mhath

Posts: 171
Black Isle, Scotland
Gender: male

Re: Optimiser for Android
Reply #99 - 06/21/13 at 05:39:40

Yup. Needed to clear the browser cache though. It did have a penchant for the .odt file!!
BTW. Just getting back to the 1100 sportie and I note the throttle dial has a numerical tps value and er.. another which looks to be a follower of the needle. Can't find mention in the instructions to these. Is the number of value? How do you see it being useful? Just curious.
Also when the log gives +8.6 or whatever on the grid and I chose apply, how do I know it does and more importantly how do I know it doesn't if I repeat the task. Maybe have to compare the two maps. Its been a while since I had a good play with this. Suffering from withdrawal symptoms.

Back to top

MG Sport 1100 inj
Triking
Honda ST1100
V7 Stone

IP Logged

YaBB Administrator YaBB Administrator Offline I love YaBB! Posts: 679 The Land of YaBB	Re: Optimiser for Android Reply #100 - 06/21/13 at 07:13:00 Re browser, you need to reload the frame. For some silly reason the normal refresh doesn't reloaded frames in a page. The throttle value would be the index of the map with fractional parts, ie idle 0.0 Did you have a read of the manual ( the odt file or one of the other options. ) That might make that clearer.
Back to top	The Administrator. IP Logged

Mad Farquhar Full Member Offline Slainthe mhath Posts: 171 Black Isle, Scotland Gender:	Re: Optimiser for Android Reply #101 - 06/21/13 at 12:31:09 Re: throttle and index fraction:- Ah! I failed to make the final link - just lazy. RTFM? Now that's a good idea. Perhaps I should edit: OK - re-read and understood - need to action AND send/save to ecu or file. Will have a play this am.
Back to top	« Last Edit: 06/21/13 at 17:34:00 by Mad Farquhar » MG Sport 1100 inj Triking Honda ST1100 V7 Stone IP Logged

Mad Farquhar

Full Member

Offline

Slainthe mhath

Posts: 171
Black Isle, Scotland
Gender: male

Re: Optimiser for Android
Reply #102 - 07/08/13 at 02:02:21

I am having trouble with v0.95. The app fails when I try to edit >a< map cell.

I load the map from ecu ( it does it automatically I see ) and the device automatically pairs which is right grand. Then in adjust map tables sub menu I select edit cell(s), hit a cell, get the yellow circle and edit selected get "Unfortunately, MyECU Optimiser v0.95 has stopped" message. Bike ignition is on and not turning during this process.

Back to top

MG Sport 1100 inj
Triking
Honda ST1100
V7 Stone

IP Logged

YaBB Administrator YaBB Administrator Offline I love YaBB! Posts: 679 The Land of YaBB	Re: Optimiser for Android Reply #103 - 07/08/13 at 07:47:45 The map loaded is the last one from file, not the ECU Can you repro the problem and send me log and map.
Back to top	The Administrator. IP Logged

Stef G Canada

YaBB Newbies

Offline

I love MyECU!

Posts: 12

Re: Optimiser for Android
Reply #104 - 07/13/13 at 19:12:38

Cliff,

not sure it will head you in a possible direction for a fix, but I had this exact same issue before I replaced the last failed cap, if you remember the one, it was C5: it was making cold starts impossible since it did not spark at crank speeds. Since I fixed it by replacing the cap, I stopped having the issue. Just an idea, but it could be the board itself, with a failed component somewhere. Then again, a symptom similar may have different causes, but this failed C5 created this problem with the optimiser for me. I also got the issue if I had 'tabs' instead of spaces in the map, or an extra empty line between the big map blocks, i.e. 2 lines empty rather than 1. Loading the base map to test helped me identify the issue was with the map (when it was not the failed c5).

Stef

Back to top

« Last Edit: 07/13/13 at 19:15:17 by Stef G Canada »

IP Logged

	Welcome, Guest. Please Login or Register
	Welcome to our forum.